Investigation into adsorption equilibrium and thermodynamics for water vapor on montmorillonite clay

The isothermal adsorption curves for water vapor on montmorillonite were measured by a gravimetric adsorption system. Dent's model was employed to estimate the adsorption behaviors of water vapor on primary adsorption sites and secondary adsorption sites. The thermodynamics analysis of water vapor adsorption was performed. At low vapor pressure region, primary adsorption predominates, and with increasing vapor pressure, secondary adsorption becomes notable. Primary adsorption sites have an evidently stronger adsorption affinity than secondary adsorption sites. With increasing vapor pressure, Gibbs free energy variation rapidly increases and then reduces slowly. Although increasing vapor pressure raises adsorption spontaneity on primary adsorption sites, the enhancement in vapor pressure decreases the spontaneity of water vapor adsorption on secondary adsorption sites. As adsorbed loading increases, isosteric heat of adsorption and entropy loss decrease first and then increase quickly. The gradually growing water clusters are responsible for the increase of entropy loss at late stage.     

Feasibility of high performance in p-type Ge1−xBixTe materials for thermoelectric modules

GeTe is a promising candidate for the fabrication of high-temperature segments for p-type thermoelectric (TE) legs. The main restriction for the widespread use of this material in TE devices is high carrier concentration (up to ∼ 10²¹ cm⁻³), which causes the low Seebeck coefficient and high electronic component of thermal conductivity. In this work, the band structure diagram and phase equilibria data have been effectively used to attune the carrier concentration and to obtain the high TE performance. The Ge_1−xBi_xTe (x = 0.04) material prepared by the Spark plasma sintering (SPS) technique demonstrates a high power factor accompanied by moderate thermal conductivity. As a result, a significantly higher dimensionless TE figure of merit ZT = 2.0 has been obtained at ∼ 800 K. Moreover, we are the first to propose that application of the developed Ge_1−xBi_xTe (x = 0.04) material in the TE unicouple should be accompanied by SnTe and CoGe₂ transition layers. Only such a unique solution for the TE unicouple makes it possible to prevent the negative effects of high contact resistance and chemical diffusion between the segments at high temperatures.     

Corrosive wear behavior of HVOF-sprayed micro-nano-structured Cr3C2–NiCr cermet coatings under aqueous media

A novel micro-nano-structured Cr₃C₂–NiCr cermet coating was prepared on 316L stainless steel by high-velocity oxygen fuel spraying technology (HVOF). Cermet coatings with different contents of micro-and nano-sized Cr₃C₂ particles as the hard phase and a NiCr alloy matrix as the bonding phase were prepared and characterized in terms of porosity, microhardness, and corrosive wear resistance in a 3.5% NaCl solution and artificial seawater. Compared to nanostructured coatings, micro-nano-structured coatings avoid decarburization and reduce nanoparticle agglomeration during the spray process, and mechanical and electrochemical properties were improved in comparison with those of conventional coatings. The micro-nano-structured Cr₃C₂–NiCr coating rendered low porosity (≤0.34%) and high microhardness (≥1105.0HV_0.3). The coating comprising 50% nano-sized Cr₃C₂ grains exhibited the best corrosive wear resistance owing to its densest microstructure and highest microhardness. Furthermore, compared to static corrosion, the dynamic corrosion of the coatings led to more severe mechanical wear, because corrosion destroyed the coating surface and ions promoted corrosion to invade coatings through the pores during corrosion wear.     

Synthesis and characterization of SrFeOx hetero-film resistance-switching device with low operation voltage

As a critical topological phase transition material, SrFeO_x could play an essential role in the field of resistive memory. How to implement resistance-switching more softly and ensure the stability of materials has always been a relevant research hotspot. Regulating the oxygen environment during the deposition process of the films can effectively control the stoichiometry of the functional layer and then improve the resistance-switching characteristics of the device. In this paper, a SrFeO_x hetero-film was prepared by oxygen pretreatment on the SrRuO₃ surface before SrFeO_x deposition, and the as-assembled micrometer-scale device exhibits a low set operating voltage of 0.6 V and favorable cycling characteristics. The SrFeO_x hetero-film reveals a vertical brownmillerite superlattice-like structure with ～20 nm perovskite buffer layer, which benefits the connection and rupture of conductive filament. Additionally, XPS and UV–vis were used to analyze the bonding energy and band gap of SrFeO_x hetero-film, and offers the experimental basis for the explanation of the conductive mechanism. Therefore, the device based on SrFeO_x hetero-film with low operation voltage provides a reference for low power consumption research on topological phase transition material.     

Analysis of suitability of TPP ash-slag waste as materials for hydrogen fuel storage

The current trends in energy were described, the main of which is the use of alternative energy sources, especially hydrogen. The most common methods of hydrogen accumulation were proposed: accumulation of compressed gaseous hydrogen in high-pressure tanks; accumulation of liquid hydrogen in cryogenic tanks; storing hydrogen in a chemically bound state; accumulation of gaseous hydrogen in carriers with a high specific surface area. Based on the combination of advantages and disadvantages, the most promising methods of accumulation were selected: storage of liquid hydrogen and storage of hydrogen in carriers with a high specific surface area. The main requirement for materials for hydrogen storage by these methods was revealed – a high specific surface area. Prospects for the development of waste-free low-emission technologies due to the recycling of secondary raw materials and the development of low-temperature technologies for the synthesis of functional and structural materials were substantiated. The applicability of large-scale ash and slag waste from coal-fired thermal power plants as a raw material for obtaining materials by low-temperature technologies was shown. The traditional ways of using ash and slag waste as a raw material, active additive and filler in the production of cements were described. Modern technologies for the production of innovative materials with a unique set of properties were presented, namely carbon nanotubes, silica aerogel and geopolymer materials. The prospect of using geopolymer matrices as a precursor for the synthesis of a number of materials was described; the most promising type of materials was selected – geopolymer foams, which are mainly used as sorbents for purifying liquids and gases or accumulating target products, as well as heat-insulating materials. The possibility of obtaining products of any shape and size on the basis of geopolymer matrices without high-temperature processing was shown. The special efficiency of the development of the technology of porous granules and powders obtained from a geopolymer precursor using various methods was substantiated. The obtained granules can be used in the following hydrogen storage technologies: direct accumulation of hydrogen in porous granules; creation of insulating layers for liquid hydrogen storage units.     

面向智慧小镇建设的机房电气管线多目标优化布置方法

常规的管线布置优化方法难以在优化过程中得到全局搜索的最优解,导致安全性能无法得到保障,因此面向智慧小镇建设设计一个新的机房电气管线多目标优化布置方法。设置电气管线约束条件,将电压均值、单位时间内电流量、电气管线损耗恢复能力作为目标函数。优化管线布置全局搜索,使用交叉操作的方式不断得到更优解。建立多目标优化电气管线模型,得到电气管线多目标优化的数学模型。通过实验数据可知,该管线布置方法在算法测试中优于常规的3种算法,且在安全性能的检测中只与标准最优值相差6.22×10⁴,3个常规方法与标准最优值的差距为6.813×10⁴、7.6×10⁴、8.32×10⁴,因此可知该多目标优化的管线布置方法可以得到更优解。     

Germination improves the functional properties of soybean and enhances soymilk quality

The effects of soybean variety and germination time on structural changes, antinutritional factor content, antioxidant activity of germinated soybean, and on the functional properties of soymilk were comprehensively investigated. The results showed that the antioxidant activity increased with increasing germination time. The content of antinutritional factors decreased with increasing germination time. Soybean varieties with the lowest tannin and trypsin inhibitor content were DN690 and HJ1. Lipoxygenase activity and phytic acid content showed no significant differences among soybean varieties. The content of α-helices and β-turns in soybean protein decreased with increasing germination time, while the content of β-sheets was increased. Soybean protein was progressively broken down into smaller molecular peptides during the germination process. The digestion and content of soluble protein in soymilk increased with germination. In summary, we show that germination is an effective, cheap, and green method that improves the functional properties of soybean and soymilk.